Applications | Standards | Corrosion Resistance | Chemical Analysis
Mechanical Properties | Processing | Welding

Alloy SAF 2507 is a super duplex stainless steel with 25% Chromium, 4% Molybdenum, 7% Nickel designed for demanding applications which require exceptional strength and corrosion resistance, such as chemical process, petrochemical and seawater equipment. The steel has excellent resistance to chloride stress corrosion cracking, high thermal conductivity and a low coefficient of thermal expansion. The high chromium, molybdenum and nitrogen levels provide excellent resistance to pitting, crevice and general corrosion.

The impact strength is also high. Alloy SAF 2507 is not recommended for applications which require long exposures to temperatures above 570ÅF because of the risk of a reduction in toughness.

• Oil and gas industry equipment
• Offshore platforms, heat exchangers, process and service water systems, fire-fighting systems, injection and ballast water systems
• Chemical process industries, heat exchangers, vessels, and piping
• Desalination plants, high pressure RO-plant and seawater piping
• Mechanical and structural components, high strength, corrosion-resistant parts
• Power industry FGD systems, utility and industrial scrubber systems, absorber towers, ducting, and piping

Standards
ASTM/ASME .......... A240 - UNS S32750
EURONORM............ 1.4410 - X2 Cr Ni MoN 25.7.4
AFNOR.................... Z3 CN 25.06 Az

Isocorrosion curves, 0.1 mm/year, in sulfuric acid
with an addition of 2000 ppm chloride ions

Isocorrosion curves, 0.1 mm/year, in hydrochloric acid.
Broken line curve represents the boiling point

Critical Pitting Temperature (CPT) range for
various alloys in 1M NACl

Critical Crevice Corrosion Temperature (CCT)
for various alloys in 10% FeCl₃

Intergranural Corrosion
SAF 2507’s low carbon content greatly lowers the risk of carbide precipitation at the grain boundaries during heat treatment; therefore, the alloy is highly resistant to carbide-related intergranular corrosion.

Stress Corrosion Cracking
The duplex structure of SAF 2507 provides excellent resistance to chloride stress corrosion cracking (SCC).

Because of its higher alloy content, SAF 2507 is superior to 2205 in corrosion resistance and strength. SAF 2507 is especially useful in offshore oil and gas applications and in wells with either naturally high brine levels or where brine has been injected to enhance recovery.

Pitting Corrosion
Different testing methods can be used to establish the pitting resistance of steels in chloride-containing solutions. The data above were measured by an electrochemical technique based on ASTM G 61. The critical pitting temperatures (CPT) of several high-performance steels in a 1M sodium chloride solution were determined. The results illustrate the excellent resistance of SAF 2507 to pitting corrosion. The normal data spread for each grade is indicated by the dark gray portion of the bar

Crevice Corrosion
The presence of crevices, almost unavoidable in practical constructions and operations, makes stainless steels more susceptable to corrosion in chloride enviroments. SAF 2507 is highly resistant to crevice corrosion. The critical crevice corrosion temperature of SAF 2507 and several other high-performance stainless steels are shown above.

Mechanical Properties
Mechanical and Physical Properties
SAF 2507 combines high tensile and impact strength with a low coefficient of thermal expansion and high thermal conductivity. These properties are suitable for many structural and mechanical components. The low, ambient, and elevated temperature mechanical properties of SAF 2507 sheet and plate are shown below. All of the test data shown are for samples in the annealed and quenched condition.

SAF 2507 is not recommended for applications which require long exposures to temperatures in excess of 570ÅF because of the increased risk of a reduction in toughness. The data listed in this brochure are typical for wrought products and should not be regarded

Mechanical Properties

Low Temperature Impact Properties

Elevated Temperature Tensile Properties

Physical Properties

Processing
Hot Forming
SAF 2507 should be hot worked between 1875ÅF and 2250ÅF. This should be followed by a solution anneal at 1925ÅF minimum and a rapid air or water quench.

Cold Forming
Most of the common stainless steel forming methods can be used for cold working SAF 2507. The alloy has a higher yield strength and lower ductility than the austenitic steels so fabricators may find that higher forming forces, increased radius of bending, and increased allowance for springback are necessary. Deep drawing, stretch forming, and similar processes are more difficult to perform on SAF 2507 than on an austenitic stainless steel. When forming requires more than 10% cold deformation, a solution anneal and quench are recommended.

Heat Treatment
SAF 2507 should be solution annealed and quenched after either hot or cold forming. Solution annealing should be done at a minimum of 1925ÅF. Annealing should be followed immediately by a rapid air or water quench. To obtain maximum corrosion resistance, heat treated products should be pickled and rinsed.

Welding
SAF 2507 possesses good weldability and can be joined to itself or other materials by shielded metal arc welding (SMAW), gas tungsten arc welding (GTAW), plasma arc welding (PAW), flux cored wire (FCW), or submerged arc welding (SAW). 2507/P100 filler metal is suggested when welding SAF 2507 because it will produce the appropriate duplex weld structure.

Preheating of SAF 2507 is not necessary except to prevent condensation on cold metal. The interpass weld temperature should not exceed 300ÅF or the weld integrity can be adversely affected. The root should be shielded with argon or 90% N₂/10% H₂ purging gas for maximum corrosion resistance. The latter provides better corrosion resistance.

If welding is to be done on only one surface and post weld cleaning is not possible, GTAW is suggested for root passes. GTAW or PAW should not be done without a filler metal unless post weld cleanup is possible. A heat input of 5-38 kJ/in. should be used for SMAW or GTAW. A heat input of about 50kJ/in. can be used for SAW.

NOTE
2205 Code Plus Two is a registered trademark of AvestaPolarit, Inc. 254 SMO and 654 SMO are registered trademarks of AvestaPolarit Stainless. SAF 2304 and SAF 2507 are registered trademarks of Sandvik AB.

This technical data and information represents our best knowledge at the time of printing. However, it may be subject to some slight variations due to our ongoing research program on corrosion resistant grades.

We, therefore, suggest that information be verified at time of inquiry or order. Furthermore, in service, real conditions are specific for each application. The data presented here is only for the purpose of description and may only be considered as guarantees when our Company has given written formal approval.